Remington 1816 Commemorative longrifle,
.50 caliber, 39" barrel,
maple, brass, patchbox, used

Part Number: AAW-177
Availability: Item has been shipped out for inspection, and at this time, is NOT available. You can click "Notify Me" and enter your email address.  We will notify you IF this item becomes available again.
  
This sleek flint Remington 1816 Commemorative longrifle is .50 caliber, with 39" octagon barrel, silver blade front sight, buckhorn rear sight, and brass furniture. Stocked in curly maple, with subtle but attractive tiger-stripe figure from muzzle to butt. Made for a tall man, the trigger reach is 14", to fit a 6' or taller shooter. These were said to be limited to 1000 rifles and this is rifle 353. Their is much conjecture as to if these rifles were made by the Remington Custom shop, contracted to Hatfield, or Pedersoli as the rifles share many similarities to products they offered and they may have indeed been sub-contractors. Trigger reach is 14" to fit today's average size shooter. Weight is 7.7 pounds.

The 39" octagon barrel is marked .50 cal and Remington on the top flat. The barrel is polished and finished chocolate brown. The bore is bright and has been well maintained. The breech end does have a few marks from the frizzen just touching the brown. The front sight is a nickel silver blade, with brass base. The rear sight is a percussion era buckhorn rear sight. The dovetail was peened along the rear edge to hold this sight, which is very common on these rifles. The rear sight is positioned 11" ahead of the breech, about 2" behind the balance point, in the location much preferred by older shooters with corrective lenses.

The curly maple stock is stained to a dark brown with a golden undertone. The stock does have a few handling marks. The buttstock is fitted with a deep crescent buttplate in mid-to late 19th century style. The brass patchbox is mounted with brass screws and engraved with decorative scrolls. The door is a cam-over center design and the spring is no longer holding the door fully shut. The Lancaster County influenced brass triggerguard has a wide open bow for the double set triggers. The forend and forearm have small brass inlays. The ramrod pipes are mounted with screws to the bottom of the barrel, which is similar to Pedersoli Frontier rifles.

The large rifle size flat faced Ketland styled flint lock is browned to match the barrel. The frizzen does show normal marks from sparking, and the barrel does have a rub mark from the frizzen just touching the side. The flint cock does have a small amount of play on the tumbler shank. Ignition is aided by the stainless steel vent liner, perfectly centered and correctly positioned well above the pan, to serve as a window on the center of the priming flash. Double lever double set triggers are correctly tuned to fire set or unset. You may cock the lock, or set the triggers, in any sequence. A tiny adjustment screw, between the two triggers, controls trigger release in the set position.

Used with some marks on the stock and barrel finish. The bore is bright and has been well maintained. Order it for a ten day visual inspection. You will be delighted. Else if it does not fit you, return it in unfired condition for same-day refund. Postage is your only risk, when you order any one-of-a-kind gun from Track, whether new, used, or antique.
.490" round balls, pure lead, Hornady, per 100
.490" round balls, pure lead, Hornady, per 100
Part Number: BALL-490
Availability: In Stock
Price: $16.99
Order Quantity:
.490" round balls, pure lead, hand cast, per 100
.490" round balls, pure lead, hand cast, per 100
Part Number: BALL-490-X
Availability: In Stock
Price: $18.59
Order Quantity:
Track's best Black Powder BORE CLEAN Solvent, with flip-top spout
Track's best Black Powder BORE CLEAN Solvent, with flip-top spout
Part Number: BORE-CLEAN
Availability: In Stock
Price: $4.59
Order Quantity:
Ball puller, steel screw, .50 caliber brass collar, 10-32 thread
Ball puller, steel screw, .50 caliber brass collar, 10-32 thread
Part Number: BP-50-10
Availability: In Stock
Price: $3.99
Order Quantity:
Flint priming flask, throws about 3 grains, brass
Flint priming flask, throws about 3 grains, brass
Part Number: FLASK-PP-3
Availability: In Stock
Price: $19.99
Order Quantity:
Cylindrical Brass Powder Flask,
5" length, 1-1/4" diameter
accepts 10-1mm threaded spouts
Cylindrical Brass Powder Flask, 5" length, 1-1/4" diameter accepts 10-1mm threaded spouts
Part Number: FLASK-PS
Availability: In Stock
Price: $34.99
Order Quantity:
Fouling Scraper, flat face, brass, .50 caliber, 10-32 thread
Fouling Scraper, flat face, brass, .50 caliber, 10-32 thread
Part Number: FS-50-10
Availability: In Stock
Price: $4.09
Order Quantity:
Powder Horn,
large, 11 to 14",
with antique patina finish
Powder Horn, large, 11 to 14", with antique patina finish
Part Number: HORN-A-L
Availability: Out of Stock, request notification when available.
Price: $74.50
  
Priming Horn,
small, 4 to 5",
with antique patina finish
Priming Horn, small, 4 to 5", with antique patina finish
Part Number: HORN-A-S
Availability: Out of Stock, request notification when available.
Price: $62.50
  
Jag, jagged cleaning tip, brass, .50 caliber, 3/8 rod, 10-32 thread
Jag, jagged cleaning tip, brass, .50 caliber, 3/8 rod, 10-32 thread
Part Number: JS-50-6-10
Availability: In Stock
Price: $4.59
Order Quantity:
Powder measure, brass, adjustable 0 to 120 grains, with spout
Powder measure, brass, adjustable 0 to 120 grains, with spout
Part Number: MAS-120
Availability: In Stock
Price: $20.99
Order Quantity:
Trapper's MINK OIL TALLOW,
patch grease,
for match shooting & cold weather hunting,
one 8 oz. tin
Trapper's MINK OIL TALLOW, patch grease, for match shooting & cold weather hunting, one 8 oz. tin
Part Number: MINK-OIL
Availability: In Stock
Price: $8.59
Order Quantity:
Shooting patches, .015" cotton, .50 - .59 caliber, per 100, dry
Shooting patches, .015" cotton, .50 - .59 caliber, per 100, dry
Part Number: OX-15-50-D
Availability: In Stock
Price: $4.79
Order Quantity:
Cleaning Patches, 2-1/2" diameter, bag of 100, pure cotton flannel, for .45 to .58 caliber
Cleaning Patches, 2-1/2" diameter, bag of 100, pure cotton flannel, for .45 to .58 caliber
Part Number: OX-CLEAN-58C
Availability: In Stock
Price: $5.79
Order Quantity:
Pick & Pan Brush,
with brass chain, button clasp,
and black bristle brush,
for flint musket, rifle, or fowler
Pick & Pan Brush, with brass chain, button clasp, and black bristle brush, for flint musket, rifle, or fowler
Part Number: PICK-BRUSH-H
Availability: In Stock
Price: $14.99
Order Quantity:
Ramrod for a Hatfield longrifle in .45, .50, or larger caliber,
 9mm (.354") stained hickory, 38-3/4" long. with brass tips threaded 10-32 at front and rear. 

Made in the USA by Track of the Wolf, Elk River, Minnesota. We turn the brass tips and assemble the ramrod.
Ramrod for a Hatfield longrifle in .45, .50, or larger caliber, 9mm (.354") stained hickory, 38-3/4" long. with brass tips threaded 10-32 at front and rear. Made in the USA by Track of the Wolf, Elk River, Minnesota. We turn the brass tips and assemble the ramrod.
Part Number: RAMROD-386-HATFIELD
Availability: In Stock
Price: $34.99
Order Quantity:
Ramrod, 5/16" stainless, 44" long rod, Creedmoor, rigid handle, 10-32 thread
Ramrod, 5/16" stainless, 44" long rod, Creedmoor, rigid handle, 10-32 thread
Part Number: RAMROD-C-44-10
Availability: In Stock
Price: $43.50
Order Quantity:
Timothy Pickering's Tool,
medium size, for flint rifles & fowling guns,
the first U. S. issue gun tool,
designed by our first U. S. Quartermaster
Timothy Pickering's Tool, medium size, for flint rifles & fowling guns, the first U. S. issue gun tool, designed by our first U. S. Quartermaster
Part Number: TOOL-PICK-M
Availability: In Stock
Price: $11.99
Order Quantity:
Primitive Rifleman's Turn Screw, hand forged tempered steel screwdriver, to fit in a longrifle patchbox
Primitive Rifleman's Turn Screw, hand forged tempered steel screwdriver, to fit in a longrifle patchbox
Part Number: TOOL-TURN-U
Availability: In Stock
Price: $8.99
Order Quantity:
Patch puller, corkscrew worm, steel, brass base, 10-32 thread
Patch puller, corkscrew worm, steel, brass base, 10-32 thread
Part Number: WORM-CORK-10
Availability: Out of Stock, request notification when available.
Price: $6.89
  
 
Track of the Wolf, Inc.
18308 Joplin St NW
Elk River, MN 55330-1773

For your convenience you can contact us via our on-line form
Contact the Webmaster if you have any problems with this site.
Privacy Policy        Copyright © 2024Track of the Wolf, Inc.
Accepted Credit Cards